CONGRATULATIONS on purchasing a Pearl Philharmonic Snare Drum. This instrument represents the state of the art in an orchestral snare drum with many new and unique features. These drums were designed in conjunction with many top orchestral players to produce the best possible sound, highest quality, and ease of operation to provide a lifetime of beautiful sound and flawless operation. Please read the following instructions to assist you with your new and unique instrument in order to appreciate the full musical and mechanical possibilities.

CUSTOM FEATURES:

TRIAD SILENT STRAINER SYSTEM, THREE SNARE TYPES, CUSTOM CABLE SNARES INCLUDING GRADUATED AND EVEN TENSION, THREE INDIVIDUAL THUMBSCREW TENSION ADJUSTERS,

EASY ON/OFF SNARE MOUNTING (drum key only, no tools required), SNARE BRIDGE, VINTAGE STYLE SNARE BED, SOLID MAPLE SHELL, CAST ALUMINUM SHELL, VINTAGE STYLE TUBE LUGS

FIRST TIME SET UP/FINE TUNING

A. HEADS: Your Pearl Philharmonic is shipped with a Remo Diplomat batter head and a Remo Diplomat snare head. Plastic heads generally take about three months to settle and reach an optimum point of stretch. You may tune your drum as you wish, however we recommend that you initially tune your batter head in the range of G-Bb for 6.5 drum and Ab-B for a 5.0 drum. The bottom head should sound a harmonic fifth above the batter head on a 6.5 drum and a harmonic fourth above on a 5.0 drum. Note: It is extremely difficult to hear the harmonic pitch described. However, if you simply place your drum on a stand with the snare strainer turned OFF and lightly tap both heads individually about two inches from the rim, you should be able to hear it. You must do this in a good quiet environment. It is also recommended that you check the pull down evenness of the heads via a ruler or a veneer caliper. Either one will help make sure that you are at a good starting point by measuring the relation of the counter hoop to the head or the counter hoop to the top of the lugs. You should then listen and clear the head by ear once you have made these initial adjustments. Be sure not to try and bring your drum up to its highest possible range right away. Allow your heads to stretch and settle slowly at least over a few weeks or you will only over torque them and render them useless. The sound will become dull and devoid of tone and ring.

B. STRAINER AND BUTT: The unique Triad Silent Strainer requires virtually no adjustment whatsoever. Designed with that in mind, it offers the smoothest and most quiet operation possible, even with one finger and at high snare tension levels. The feel remains light and smooth no matter how you like your snares adjusted, and they can be turned on and off quickly and effortlessly during the softest musical passages.

BUTT: The snare butt offers a master tension adjustment to tighten or loosen all snares simultaneously. It also offers three easy on/off drum key screws to quickly change snare sets WITHOUT THE USE OF TOOLS! All you need is your drum key (included) to change a set of snares. No allen wrenches, no pliers, no cumbersome mounting cables or strings. Note: WARNING!!! NEVER UNSCREW OR TAMPER WITH THE SOCKET HEAD SCREWS WHICH CLAMP CABLES IN PLACE, THESE ARE PERMANENT!!!

REMOVING SNARES: If you wish to change a set of snares and create your own combinations from original Pearl parts, simply unscrew the thumb tension knob on the strainer side completely, then unscrew the corresponding drum key screw on the butt side. It’s that simple! It was designed with speed and ease of operation in mind so that you can change a set of snares in 60 seconds.

C. SNARE FEATURES: Your Pearl Philharmonic Snare System has several unique features. The COATED CABLE is clamped in permanently with a graduated tension system. This gives you the maximum dynamic range possible from this set of cables which are intended for the loudest dynamic ranges. Other systems generally have these cables all at one tension which require the player to attempt to tilt these snares to achieve a graduated tension, which is cumbersome, requires tools, and is usually a failure. Without our unique graduated tension snares, the higher tension required for their dynamic range only causes choking of the bottom head and poor loud snare response. The COATED CABLE is designed to respond perfectly and effectively from ff to mf respectively without any gaps in that range and without distorting or choking the sound of the bottom head. The UNCOATED STAINLESS cable is clamped in permanently as well, but is set in an even tension system. This provides extremely even snare contact with the bottom head for the mf to mp dynamic range without distorting the sound of the bottom head due to their significantly lower tension level. The SNAPPY WIRE snares are placed in the middle of the other two to assure perfect flat contact with the snare head which minimizes excess snare buzz, and provides a superior soft dynamic snare response. They are intended for the mp to ppp dynamic range and are deliberately not plated steel wires which provides 100% more snare presence and response than chromed wires.

D. SNARE BRIDGE: The snare bridge is designed to assist the way all snares lay in the snare bed thus providing perfect snare level contact with the snare head as well as facilitating the conforming of the cables to the snare bed. This feature ensures complete contact of your cables, particularly at each end of the head, where most snare systems have a slight gap between the cable and the head. The snare bed is specifically designed to be short and quick so as not to overly affect the pitch of the bottom head and facilitate complete snare contact.