Tech Speak is a regular segment of the Pearl Drummers' Resources and features articles pertaining to Pearl drums and (sometimes) drumming in general. It is written by Gene Okamoto and Raymond Massey, Pearl's resident nuts and bolts guys.


FINE TUNING YOUR PEARL PHILHARMONIC FIELD DRUM
by Steve Hearn

CONGRATULATIONS on purchasing a Pearl Philharmonic Field Drum. This instrument represents the state of the art in an orchestral field drum with many new and unique features. These drums were designed in conjunction with many top orchestral players to produce the best possible sound, highest quality, and ease of operation to provide a lifetime of beautiful sound and flawless operation. Please read the following instructions to assist you with your new and unique instrument in order to appreciate the full musical and mechanical possibilities.
CUSTOM FEATURES:
TRIAD SILENT STRAINER SYSTEM, THREE SNARE TYPES, CUSTOM CABLE SNARES INCLUDING GRADUATED AND EVEN TENSION, THREE INDIVIDUAL THUMBSCREW TENSION ADJUSTERS, EASY ON/OFF SNARE MOUNTING (drum key only, no tools required), SNARE BRIDGE, VINTAGE STYLE SNARE BED, PLY MAPLE SHELL, VINTAGE STYLE TUBE LUGS

FIRST TIME SET UP/FINE TUNING

A. HEADS:Your Pearl Philharmonic is shipped with a Remo Diplomat batter head and a Pearl Diplomat snare head. Plastic heads generally take about three months to settle and reach an optimum point of stretch. You may tune your drum as you wish, however we recommend that you initially tune your batter head in the range of Bb-C# for 16X16 drum and E-G for a 14X12 drum. The bottom head should sound higher than the batter head. Note: Simply place your drum on a stand with the snare strainer turned OFF and lightly tap both heads individually about two inches from the rim, you should be able to hear it. You must do this in a good quiet environment. It is also recommended that you check the pull down evenness of the heads via a ruler or a veneer caliper. Either one will help make sure that you are at a good starting point by measuring the relation of the counter hoop to the head or the counter hoop to the top of the lugs. You should then listen and clear the head by ear once you have made these initial adjustments. Be sure not to try and bring your drum up to its highest possible range right away. Allow your heads to stretch and settle slowly at least over a few weeks or you will only over torque them and render them useless. The sound will become dull and devoid of tone and ring.

B. STRAINER AND BUTT: The unique Triad Silent Strainer requires virtually no adjustment whatsoever. Designed with that in mind, it offers the smoothest and most quiet operation possible, even with one finger and at high snare tension levels. The feel remains light and smooth no matter how you like your snares adjusted, and they can be turned on and off quickly and effortlessly during the softest musical passages.

BUTT: The snare butt offers a master tension adjustment to tighten or loosen all snares simultaneously. It also offers three easy on/off drum key screws to quickly change snare sets WITHOUT THE USE OF TOOLS! All you need is your drum key (included) to change a set of snares. No allen wrenches, no pliers, no cumbersome mounting cables or strings. Note: WARNING!!! NEVER UNSCREW OR TAMPER WITH THE SOCKET HEAD SCREWS WHICH CLAMP CABLES IN PLACE, THESE ARE PERMANENT!!!

REMOVING SNARES: If you wish to change a set of snares and create your own combinations from original Pearl parts, simply unscrew the thumb tension knob on the strainer side completely, then unscrew the corresponding drum key screw on the butt side. It's that simple! It was designed with speed and ease of operation in mind so that you can change a set of snares in 60 seconds.

C. SNARE FEATURES: Your Pearl Philharmonic Field Drum Snare System has several unique features. One COATED CABLE is clamped in permanently with a graduated tension system while the other is clamped in permanently with an even tensioned system. Graduated tension can be felt by lightly brushing the coated cable with your finger. The graduated tension snare unit will feel tight-to-looser as you brush from one side to the other. The even tensioned snares will feel even throughout the 5 individual snares. This gives you the maximum dynamic range possible from these sets of cables which are intended for the loudest to medium soft dynamic ranges. Other systems generally have these cables all at one tension which require the player to attempt to tilt these snares to achieve a graduated tension, which is cumbersome, requires tools, and is usually a failure. Without our unique graduated tension snares, the higher tension required for their dynamic range only causes choking of the bottom head and poor loud snare response. The COATED CABLE is designed to respond perfectly and effectively from ff to mp respectively without any gaps in that range and without distorting or choking the sound of the bottom head. The UNCOATED STAINLESS cable is clamped in permanently as well, but is set in an even tension system. This provides extremely even snare contact with the bottom head for the mf to pp dynamic range without distorting the sound of the bottom head due to their significantly lower tension level.

D. SNARE BRIDGE: The snare bridge is designed to assist the way all snares lay in the snare bed thus providing perfect snare level contact with the snare head as well as facilitating the conforming of the cables to the snare bed. This feature ensures complete contact of your cables, particularly at each end of the head, where most snare systems have a slight gap between the cable and the head. The snare bed is specifically designed to be short and quick so as not to overly affect the pitch of the bottom head and facilitate complete snare contact.

E. FINE TUNING THE SNARES: Turn the strainer to the ON position. First, make sure all three sets of snares are completely disengaged and are not touching the bottom head. Begin with your GRADUATED COATED CABLE by turning the thumb screw clockwise until they begin to engage. As they come into range, strike the drum at a f to ff volume so that they are filling that dynamic range. Next, repeat this procedure with the EVEN COATED CABLE by turning the thumb screw clockwise until they being to engage in the f to mf dynamic range. Next, repeat this procedure with your UNCOATED STAINLESS cable. Turn the thumb knob clockwise until they fill the mf to pp dynamic range while striking the drum at that volume. Leave your strainer in the ON position when storing your drum. This will facilitate the conformation of the cables to the snare bed and snare bridge which will eventually create a "custom snare fit" to the drum over time, improving their sound and response.